Unanswered topics • Active topics

Deleted..

Need technical advice ?
Post Reply
paxidorm
3000rpm
3000rpm
Posts: 78
Joined: Fri Dec 18, 2009 6:54 pm

Deleted..

Post by paxidorm » Fri Jun 25, 2010 12:39 pm

Deleted
Last edited by paxidorm on Mon Aug 09, 2010 10:20 am, edited 1 time in total.
Top
User avatar
chayfoocheong
4000rpm
4000rpm
Posts: 132
Joined: Tue Nov 17, 2009 1:23 pm
Location: Singapore

Post by chayfoocheong » Fri Jun 25, 2010 11:27 pm

Personally, I am not sure if bigger dia is better. I am definitely sure the intake air pressure the higher the better. We don't need rocket science to prove.
Contrary, turbo charge is using the same philosophy to boost higher air pressure intake.
Top
paxidorm
3000rpm
3000rpm
Posts: 78
Joined: Fri Dec 18, 2009 6:54 pm

Post by paxidorm » Sun Jun 27, 2010 12:49 pm

Since I plan to upgrade my b16 intake manifold, what should i go for?

- Bore the stock b16 one?
- Type R intake manifold from ek9 or dc2?
- Skunk2?
- Any other brand?

Hard skunk 2 is good but design same as type R one? So if get type R one is a good upgrade for B16 stock intake manifold?

Pls advise.... Thank u in advance
Top
User avatar
chayfoocheong
4000rpm
4000rpm
Posts: 132
Joined: Tue Nov 17, 2009 1:23 pm
Location: Singapore

Post by chayfoocheong » Mon Jun 28, 2010 8:58 am

I would believe Type R intake manifold manufacturer would have done a lot of R&D to establish in Honda car. The curve of pipe/dia etc for Type R performance air intake demand will meet the specification.
As long as it is a establish brand (Japan type), you are rest assure.
Top
User avatar
Silver
9000rpm Rev Cut
9000rpm Rev Cut
Posts: 4788
Joined: Sun Feb 22, 2004 5:08 pm
Location: 10-pi-nee

Post by Silver » Mon Jun 28, 2010 8:40 pm

Go for a EK9 intale manifold... Its good enough for a budget run.. :) :)
Image

There's always a better 2molo...........
Top
paxidorm
3000rpm
3000rpm
Posts: 78
Joined: Fri Dec 18, 2009 6:54 pm

Post by paxidorm » Tue Jun 29, 2010 8:17 am

ok..actually interested to know whether upgrade of intake manifold to type R or skunk2 help in improving the performance in term of different RPM range. e.g. difference in high/mid/low rpm? Because from what i know B16 and type R are both 62mm
Top
Sting3Rhea
7000rpm VTEC ON
7000rpm VTEC ON
Posts: 724
Joined: Tue Apr 28, 2009 6:52 pm

Post by Sting3Rhea » Sat Jul 03, 2010 4:08 pm

EK9 and DC2R same intake manifold. Difference is only on the throttle body, EK( being 2mm smaller. You can machine them bigger by 2mm but I doubt you can feel that 2mm difference.
JDM: Making Your Car Look Like Another Stock Car.
Image
Top
User avatar
EK Type-R
8000rpm Red Line
8000rpm Red Line
Posts: 1513
Joined: Mon Feb 23, 2004 9:48 am
Location: Novena, SG

Post by EK Type-R » Sat Jul 03, 2010 10:00 pm

paxidorm wrote:ok..actually interested to know whether upgrade of intake manifold to type R or skunk2 help in improving the performance in term of different RPM range. e.g. difference in high/mid/low rpm? Because from what i know B16 and type R are both 62mm
Image

http://www.skunk2.com/engine-2.php?code=INPROB
Image
Top
User avatar
daboy14
4000rpm
4000rpm
Posts: 128
Joined: Mon Jan 18, 2010 1:45 am
Location: Singapore
Contact:
Contact daboy14

Intake

Post by daboy14 » Thu Jul 15, 2010 5:36 pm

Heya there guys..

Just to clarify things here both have the equal diameter in their plenum only diffrence is the throttle body that their using.. One is bigger by 2mm.. And the fact that dc2 has its iats (intake air temp sensor) mounted on the manifold itself while ek9 iats is located at the CAI before the throttle body..

HTH
"LIFE begins at 8.9k rpm.... VTEC power!!!
Top
Post Reply


Return to “Technical Discussion”