Unanswered topics Active topics

how to remove dents?

Need technical advice ?
User avatar
Gresini
8000rpm Red Line
8000rpm Red Line
Posts: 1673
Joined: Sun Aug 13, 2006 11:13 am
Location: Geylang
Contact:

Re: how to remove dents?

Post by Gresini » Tue Mar 23, 2010 12:01 pm

Alvinyzw wrote:Today I found a very obvious dent at my left fender tat dunnoe which f ker make it. :evil: :x Anyone know how can I remove such dents?
:twisted: :(
Cheapest DIY trial. Dry ice. leave it there for abt 30mins. Best to do on a hot afternoon. If doesnt work, go to shop.

Alvinyzw
10 000rpm Over Rev
10 000rpm Over Rev
Posts: 9136
Joined: Sat Oct 25, 2008 6:27 pm
Location: SengKang/Macpherson
Contact:

Re: how to remove dents?

Post by Alvinyzw » Tue Mar 23, 2010 7:12 pm

Gresini wrote:
Alvinyzw wrote:Today I found a very obvious dent at my left fender tat dunnoe which f ker make it. :evil: :x Anyone know how can I remove such dents?
:twisted: :(
Cheapest DIY trial. Dry ice. leave it there for abt 30mins. Best to do on a hot afternoon. If doesnt work, go to shop.
Thanks alot! :D
Image

Jarren
4000rpm
4000rpm
Posts: 97
Joined: Fri May 01, 2009 8:37 am

Post by Jarren » Tue Mar 23, 2010 7:33 pm

Kena once before at borders car pk.. the lorry which came later pk beside my car.. when i went to collect my car.. just check on my left front.. SHIT! one deep dent.. looks like this bloody driver purposely open his door hard!
I didn't give a damn.. in return gave his lorry some "nice treatment" before I left. :evil:

User avatar
Gresini
8000rpm Red Line
8000rpm Red Line
Posts: 1673
Joined: Sun Aug 13, 2006 11:13 am
Location: Geylang
Contact:

Post by Gresini » Tue Mar 23, 2010 10:50 pm

Pls note dry ice only works on minor dents, deep dents which expose primer doesnt work anymore, or rather reduce effect.

Alvinyzw
10 000rpm Over Rev
10 000rpm Over Rev
Posts: 9136
Joined: Sat Oct 25, 2008 6:27 pm
Location: SengKang/Macpherson
Contact:

Post by Alvinyzw » Wed Mar 24, 2010 7:00 pm

Gresini wrote:Pls note dry ice only works on minor dents, deep dents which expose primer doesnt work anymore, or rather reduce effect.
Thanks, will find which method is good solution soon. :wink:
Image

User avatar
wpyeo
SHC Die Hard!!!
SHC Die Hard!!!
Posts: 14667
Joined: Tue Dec 27, 2005 6:23 pm
Location: North Wanderer

Post by wpyeo » Fri Mar 26, 2010 12:58 am

Alvinyzw wrote:Nope. I always park my car passenger side mirror very near to the wall. At least 1m from the mirror to wall. :)

Anyway, my carpark got B1 & B2, B1 is always packed full of car without a lots left at nite while B2 only got few cars wif lot of lots, during the week when I didn't drive my car out, I park at B2 so... :roll:
thatz very far frm wall wor... i always try to park as close to wall as possible. sometimes my left side mirror almost touching the wall... roughly ard 2 to 3inches away nia...
ImageImage

Alvinyzw
10 000rpm Over Rev
10 000rpm Over Rev
Posts: 9136
Joined: Sat Oct 25, 2008 6:27 pm
Location: SengKang/Macpherson
Contact:

Post by Alvinyzw » Fri Mar 26, 2010 6:42 pm

wpyeo wrote:
Alvinyzw wrote:Nope. I always park my car passenger side mirror very near to the wall. At least 1m from the mirror to wall. :)

Anyway, my carpark got B1 & B2, B1 is always packed full of car without a lots left at nite while B2 only got few cars wif lot of lots, during the week when I didn't drive my car out, I park at B2 so... :roll:
thatz very far frm wall wor... i always try to park as close to wall as possible. sometimes my left side mirror almost touching the wall... roughly ard 2 to 3inches away nia...
Now I learn u liao. Mirror juz noice touch the wall, muz park carefully. :D
Image

User avatar
Gresini
8000rpm Red Line
8000rpm Red Line
Posts: 1673
Joined: Sun Aug 13, 2006 11:13 am
Location: Geylang
Contact:

Re: how to remove dents?

Post by Gresini » Mon Mar 29, 2010 10:17 am

Alvinyzw wrote:Today I found a very obvious dent at my left fender tat dunnoe which f ker make it. :evil: :x Anyone know how can I remove such dents?
Image
Image
:twisted: :(
Sir, ok to update status?

Alvinyzw
10 000rpm Over Rev
10 000rpm Over Rev
Posts: 9136
Joined: Sat Oct 25, 2008 6:27 pm
Location: SengKang/Macpherson
Contact:

Re: how to remove dents?

Post by Alvinyzw » Mon Mar 29, 2010 7:09 pm

Gresini wrote:Sir, ok to update status?
I will update when it's done, have been quite busy wif work these few days. :D
Image

Post Reply