|
(PPPLEASE DON'T PM ME ABOUT DIY STUFF.. post it in the open so everyone can share and learn.. i'm still learning too bros.. i need my PMbox space for other matters)
Hmmm personally i'm those with clumsy hands and feet so i leave everything to my mechanic,but can i just pop by and kay poh see see abit?joon wrote:ok bros.. all you guys who need to borrow my hydraulic jack etc etc.. all your PM's whatever
use the poll, we'll decide when the date when everyone can make it.. not too many tho'.. i don't have the tools for more than a few cars and you'll have to bring your own
ATF cooler = automatic transmission fluid coolertattybear wrote:ur ATF cooler is to cool the engine oil or the tranmission oil?
please feel free to add to the list below: 
bro, what time do you usually start your diy sessions and how long does it take to do heatshield and CAI for intake? i bought the heatshield from garlin and it have been sitting in my boot for months liao, just don't have time to diy....i bought the 1" thick ones, 1'x 3' cost me about $38. since you are going to give wilson pointers on his diy project, thought i might as well join in and get pointers from you too. sat is usually family day for me but i'll try to apply for gate pass for a few hrsjoon wrote:ok now i need to know roughly what you guys will be doing so i can tape up enough lots
1. Wilson - Heatshield and CAI for intake
2. Jye - TYC Projector Headlamps install
3.
4.
i think we can only handle about 4 cars or so with the tools i have, so if there's spillover (if any) then we'll hold another DIY Day Part 5 later on.. the rest of us can just help out/discuss our mods and stuff and just chillout.. maybe someone can bring some beers
but if you're coming you MUST LET ME KNOW, esp if we haven't met/seen each other before.. this is a precaution i keep, even though this gathering is on private property
yo bro! intakes normally don't take more than 1hr.. i have to admit, the master of intakes/CAI is zippyalex7Marlboroman wrote:bro, what time do you usually start your diy sessions and how long does it take to do heatshield and CAI for intake? i bought the heatshield from garlin and it have been sitting in my boot for months liao, just don't have time to diy....i bought the 1" thick ones, 1'x 3' cost me about $38. since you are going to give wilson pointers on his diy project, thought i might as well join in and get pointers from you too. sat is usually family day for me but i'll try to apply for gate pass for a few hrs
i'm hoping he can come down and give us some pointers too.. i'm very familiar with the EK chassis, but he's the one who's done quite few ES's.. so his input would be invaluable in your case, since wilson's is an EK thanks bro. where do you guys usually meet?joon wrote:yo bro! intakes normally don't take more than 1hr.. i have to admit, the master of intakes/CAI is zippyalex7Marlboroman wrote:bro, what time do you usually start your diy sessions and how long does it take to do heatshield and CAI for intake? i bought the heatshield from garlin and it have been sitting in my boot for months liao, just don't have time to diy....i bought the 1" thick ones, 1'x 3' cost me about $38. since you are going to give wilson pointers on his diy project, thought i might as well join in and get pointers from you too. sat is usually family day for me but i'll try to apply for gate pass for a few hrs
we normally try to start immediately after lunch.. some of us may meet for lunch first.. coz it's rather troublesome to washup, eat lunch, and come back and start again.. besides fri nite is our test car/discussion nite, so normally we sleep in on sat mornings hahaha
most welcome to join us bro
Joon,joon wrote:ok now i need to know roughly what you guys will be doing so i can tape up enough lots
1. Wilson - Heatshield and CAI for intake
2. Jye - TYC Projector Headlamps install
3.
4.
i think we can only handle about 4 cars or so with the tools i have, so if there's spillover (if any) then we'll hold another DIY Day Part 5 later on.. the rest of us can just help out/discuss our mods and stuff and just chillout.. maybe someone can bring some beers
but if you're coming you MUST LET ME KNOW, esp if we haven't met/seen each other before.. this is a precaution i keep, even though this gathering is on private property
yo bro! most welcome, just vote for your preferred date, then me, joe and alex will try to find a date which fits everyone.. the location is near adam road, meet at adam road hawker centre carpark, my place is within 2 minutes from theresimple wrote:Joon,
Can I join in for this coming DIY? I would be doing the rubber insulation on my aircon piping (maybe need yr help) as well as to pick up some tips from yr guys. The above date is fine with me, just need to know in advance, tks
I may install the projectors earlier than the stated date. But I'll do some other DIY on that day. Hopefully I can finish wiring up the circuit for the LEDs and install then.joon wrote:ok now i need to know roughly what you guys will be doing so i can tape up enough lots
1. Wilson - Heatshield and CAI for intake
2. Jye - TYC Projector Headlamps install
3.
4.
i think we can only handle about 4 cars or so with the tools i have, so if there's spillover (if any) then we'll hold another DIY Day Part 5 later on.. the rest of us can just help out/discuss our mods and stuff and just chillout.. maybe someone can bring some beers
but if you're coming you MUST LET ME KNOW, esp if we haven't met/seen each other before.. this is a precaution i keep, even though this gathering is on private property
