Page 13 of 19

Posted: Thu Jan 08, 2009 12:54 pm
by MCDS
Poison List

Intake /Header / Exhaust

Intake

i) Simota Aeroform : SRI with Plastic Heatshield (ard $230)
ii) Blitz Sonic : SRI with Aluminium Heatshield (w/o piping) ($560+/-)
iii) BMC : CDA ($440-480) w/o install depending on size. Auto smaller
iv) Apexi : SRI (Around 180 plus $20 bucks for adaptor)
v) K&N : Drop-in with CAI piping (less than $150)
vi) AEM V1: CAI piping with AEM open pod filter ($500+)
vii) AEM V2: SRI piping with AEM open pod filter ($570+)
viii) K&N : Open pod (model 57i) ($250)
ix) INJEN : SRI open pod : ~$400
x) NINJA-RACING: All-in-one, piping, close pod and CAI ($373)
xi) Throttle body: (S$320) include installation plus anaylsis fault.

Header

i) Hotbits Header : 4-2-1 Header (Ard $250) with flexi pipe
ii) SD Header (Non-Chrome) : 4-2-1 Header ($250) with flexi pipe from FK
iii) SD Header (Chrome) : 4-1 ($200) From FK
vi) DC sports Header 4-2-1 (Ard $700)

Exhaust

i) Supersprint : free flow muffler ($784 + $50 inspection fee, LTA approved)
ii) Hotbits : Straight through muffler ($140 with install, non LTA approved)
iii) Operated : Stock exhuast ($180++, non LTA approved)



Cooling

i) Mugen thermostat and fan switch: approx $250




Engine Oil Cooler:

ATF Cooler:

i) Hayden : $240+ w install
ii) HKS : SGD 1100
iii) ARC : SGD 2300
iv) Permacool: $220 w install



Suspension

Camber Kit :

i) SPC Front Camber Bolts : $130
ii) SPC Rear Camber Kits : $350
iii) J's Racing Rear Cambar Kit ( Ball Joint ): $ 500
iv) Kenny's Modified Stock Rear Camber Kits : $200+

Lowering Springs :

i) Tanabe NF210 (S$370++ w/install)
ii) APEX (S$350 w/install)
iii) Eibach Pro kit : $480

Coilover :

i) BC Coilover :Height + Damping Adjustatable (Ard $1250)
ii) Tomei Coilover : Height + Damping Adjustatable (Ard $980)
iii) Tein Coilover: Height + Damping Adjustatable (Ard $1800 for Tein SS)
iv) Tein Basic: Height Adjustable, Can Revalve ( RM2700)
v) Tanabe Coilover : Height Adjustatable only (ard $1900)
vi) D2 Coilover : Height + Damping Adjustatable + pillowball mount (ard $1700) best buy
vii) Hotbits Coilovers: Height adjustable only, RM2000. Revalve whole set RM480

Bars (Struts, ARBs)

i) Hotbits Tower Strut bar : ($85)
ii) Alutec Tower Strut bar : ($155)
iii) Neuspeed Tower Strut bar : ($230)
iv) Silver Front Strut Bar : ($110 w/install)
v) Summit Front Strut Bar: ($150 w/install)
vi) Summit Rear Strut Bar: ($180 w/install)
vii) DC sport front strut bar:(ard $500 w/install)
viii) OEM ES Engine Strut Bar : $75 w/ install
ix) Summit Lower Brace Bars : 2 point Bars x2 ($250 w/install)
x) Tanabe Lower Brace Bars : 4 point Bar ($250 w/install)
xi) Neuspeed X-Brace : 4 point
xii) Alutec Lower Tie Bar : ($100 w/install)
xiii) Summit Lower Tie Bar : $110 w/install
xiv) DC Sports Lower Tie Bar :
xv) Neuspeed Lower Tie Bar :
xvi) Front ARB : 25.4mm JDM ES ($180 with installation)
xvii) Rear ARB : 22mm DC5 ($180 with installation)



Brake System

Front Brakes Upgrade Kit

i) Prelude Recon : 282mm rotor + Bigger caliper ($380-$420)
ii) Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
iii) Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
iv) VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
v) FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($450-$600)

Rotors and Brake Pads

i) Brembo max slotted rotor with project mu bestop brake pads ($280 with install)
ii) Brembo Sports Rotors (slotted or cross drilled) : $380
iii) Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install
iv) project Mu bestop Brake Pads: $120 with install
v) Brembo blank rotor(282mm) redrilled: $220 w/install
vi) Ferrodo Brake Pads: $110 w/install
vii) Hawk performance pads: pm Bravo for special pricing


Project Miu Rotors, Pads - Go to Stamford Tyres (esp at Jurong)

Brembo stuff and Hawk pads, go to bro Bro
Can look for bravo here:

SPINERGY CONCEPTS
Blk 9002 Tampines St 93
#02-40 S(528836)
T: 6786 2809 (Mon~Fri, 9am~5pm - by appmt)
E: spinergyconcepts@singnet.com.sg




Rear disc conversion

i) ES3 conversion: approx $1.3k (direct plug n play, no mods req, rotor sz 260mm)
ii) EP3 conversion: approx $950 (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iii) DC5 conversion: POA (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iv) EK4 conversion: approx $800 (need to fabricate bracket, rotor sz 240mm)

Stainless steel braided hoses aka (SSBH)

i) EZess Steel braided brake hose with Teflon(4piece): $280 -$320 w/install
ii) Pro-RS PTFE Teflon Steel Braided brake hose (4piece) + 1L Ferodo brake fluid: $240 w/install
iii) Goodridge Steel braided brake hose: $200+ (front only)


Tyres

*Price depends on width and profile*

15in

i) Yokohama Advan AD07 15" 195/55/15 ($135-150)
ii) Falken RT215 15" 205/50/15 ($130-160)
iii) Goodyear Eagle F1 GSD3 [Thai]195/60/15 ($110-130)
iv) Bridgestone G3 15" ($90-120)
v) ContiPremiumContact2: 195/45/15 ($220)
vi) Hankook Ventus Prime K105 205/55R15 ($115-130each)
vii) Bridgestone RE01R 195/55/15($155-185)
viii) Bridgestone RE001 Adreneline 195/55/15($120-145)
ix) Goodyear Eagle RS Sports 195/55/15 [Made in Japan] $145
x) Goodyear Eagle Asymetric [Made in Japan] $155
xi) Toyo Proxes T1R 195/55/15$120
xii) Toyo Proxes R1R 195/55/15 $175
xiii) Toyo Proxes R888 195/55/15$175

16in

i) Yokohama ADrive R1 205/50/16 ($130)
ii) Bridgestone G3 205/50/16 inch ($130)
iii) Goodyear Eagle F1 GSD3 [Thai] 16" ($120)
iv) Toyo Proxes T1R 205/50/16 ($150/pcs)
v) Yokohama SDrive 205/50/16 ($160)
vi) Falken Ziex 326 205/50/16 ($120)


17in

i) ContiSportsContact2: 215/45/17VR ($280)
ii) Dunlop LM702: 215/45/17 ($150)
iii) Goodyear Eagle F1 GSD3: 205/45/17 [Thai] ($160)
iv) Toyo T1R: 215/45/17 ($200)
v) Bridgestone RE001: 215/45/17 ($220)
vi) Bridgestone RE01R: 215/45/17 ($250)
vii) ContiSportsContact3: 215/45ZR/17W TL XL ($300)


Electronics

i) Apex'i turbo timer: ($160)
ii) Unichip ($800+)
iii) Greddy E-manage Blue : ($500+)
iv) Apex'i VAFCII (less than $500) without install or tuning
v) Apex'i SAFCII:
vi) Apex'i RSM : $310
vii) Blitz RVit : $480
viii) Defi VSD basic: $290+
ix) HKS F-Con SZ : Install & Tune ( RM2600 )
x) SMT6: $800+
xi) Greddy E-manage Ultimate: ($1500) install+tune
xii) Pivot Raizin Voltage Stabilizer VS $98 w/o install
xiii) Pivot Raizin Voltage Stabilizer + Grounding VS-E $148 w/o install
xiv) Pivot Raizin Spark VS-S $128 w/o install
xv) Pivot Raizin Spark VS-V $228 w/o install
xvi) Pivot Spark Earth $98 w/o install

Accessories

i) CF eylids : ($180)
ii) Custom make Rear eyelids : ($220)
iii) CF hood (OEM design) : $890 (MSRP)
iv) Billion Funnel : ($55) :x
v) Bonnet Insulator: ($55)
vi) Boot Insulator: ($90)
vii) Billion Air Duct: ($150 per metre)
viii) RPM Crank Pulley with Harmonic Damper ($270)



Emblems

i) EP3 original Honda emblem : chrome 'H', red background ($60)
ii) VTEC emblem : wordings onli ($13)
iii) i-VTEC emblem : wordings onli (unknown)
iv) sticker type VTEC emblem : silver color wordings($6)
v) JDM 'FERIO' Emblem : $25
vi) Rear 'RS' Emblem : $43
vii) Front 'RS' Emblem : $19
viii) Mugen Emblem : $12


Bonnet Chrome Tip

i) Sticker: in matt/gloss black (Ask Eeee78 for Pricing)
paint on chrome strip : ($25 - $30)
ii) Removal of chrome strip + sealing up holes on bonnet + respray bonnet : ($180)
iii) Honda Original Colour Coded Grille (for ES8 & pre f/l ES5) : $63


Boot Chrome Tip

i) Sticker: (Ask Eeee78 for Pricing)
ii) Painted Chrome Tip : Front / Rear ($70)
iii) Removal of Whole Chrome Part (ard 100+)
iv) Honda Original Colour Coded Trunk (for ES8 & pre f/l ES5) : $72

Interior

i) Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.


*Prices varies, kindly call and find out actual pricing from the relevant suppliers/shops.*



Maintenance List

Aircon Compressor Unit

Markcool at Woodlands, New $460, recon $220, labour inclusive.
Look for Ah Huat, a real honest and friendly guy.

Posted: Sat Jan 17, 2009 4:47 pm
by wanhuo_ho
i) Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.

ii) Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install

iii) project Mu bestop Brake Pads: $120 with install


Hello Bro, I am interested in the above items. How may I know more deatils from you?

For items ii and iii are the price for one side or both sides?

Posted: Sun Feb 22, 2009 9:36 pm
by littleluki
Poison List

Intake /Header / Exhaust

Intake

i) Simota Aeroform : SRI with Plastic Heatshield (ard $230)
ii) Blitz Sonic : SRI with Aluminium Heatshield (w/o piping) ($560+/-)
iii) BMC : CDA ($440-480) w/o install depending on size. Auto smaller
iv) Apexi : SRI (Around 180 plus $20 bucks for adaptor)
v) K&N : Drop-in with CAI piping (less than $150)
vi) AEM V1: CAI piping with AEM open pod filter ($500+)
vii) AEM V2: SRI piping with AEM open pod filter ($570+)
viii) K&N : Open pod (model 57i) ($250)
ix) INJEN : SRI open pod : ~$400
x) NINJA-RACING: All-in-one, piping, close pod and CAI ($373)
xi) Throttle body: (S$320) include installation plus anaylsis fault.

Header

i) Hotbits Header : 4-2-1 Header (Ard $250) with flexi pipe
ii) SD Header (Non-Chrome) : 4-2-1 Header ($250) with flexi pipe from FK
iii) SD Header (Chrome) : 4-1 ($200) From FK
vi) DC sports Header 4-2-1 (Ard $700)
v) Megan Racing Sports Header 4-1 (Chrome) (Ard $240) (not available in S'pore, order from Amazon) Product No: MR-SSH-HC117

Exhaust

i) Supersprint : free flow muffler ($784 + $50 inspection fee, LTA approved)
ii) Hotbits : Straight through muffler ($140 with install, non LTA approved)
iii) Operated : Stock exhuast ($180++, non LTA approved)



Cooling

i) Mugen thermostat and fan switch: approx $250




Engine Oil Cooler:

ATF Cooler:

i) Hayden : $240+ w install
ii) HKS : SGD 1100
iii) ARC : SGD 2300
iv) Permacool: $220 w install



Suspension

Camber Kit :

i) SPC Front Camber Bolts : $130
ii) SPC Rear Camber Kits : $350
iii) J's Racing Rear Cambar Kit ( Ball Joint ): $ 500
iv) Kenny's Modified Stock Rear Camber Kits : $200+

Lowering Springs :

i) Tanabe NF210 (S$370++ w/install)
ii) APEX (S$350 w/install)
iii) Eibach Pro kit : $480

Coilover :

i) BC Coilover :Height + Damping Adjustatable (Ard $1250)
ii) Tomei Coilover : Height + Damping Adjustatable (Ard $980)
iii) Tein Coilover: Height + Damping Adjustatable (Ard $1800 for Tein SS)
iv) Tein Basic: Height Adjustable, Can Revalve ( RM2700)
v) Tanabe Coilover : Height Adjustatable only (ard $1900)
vi) D2 Coilover : Height + Damping Adjustatable + pillowball mount (ard $1700) best buy
vii) Hotbits Coilovers: Height adjustable only, RM2000. Revalve whole set RM480

Bars (Struts, ARBs)

i) Hotbits Tower Strut bar : ($85)
ii) Alutec Tower Strut bar : ($155)
iii) Neuspeed Tower Strut bar : ($230)
iv) Silver Front Strut Bar : ($110 w/install)
v) Summit Front Strut Bar: ($150 w/install)
vi) Summit Rear Strut Bar: ($180 w/install)
vii) DC sport front strut bar:(ard $500 w/install)
viii) OEM ES Engine Strut Bar : $75 w/ install
ix) Summit Lower Brace Bars : 2 point Bars x2 ($250 w/install)
x) Tanabe Lower Brace Bars : 4 point Bar ($250 w/install)
xi) Neuspeed X-Brace : 4 point
xii) Alutec Lower Tie Bar : ($100 w/install)
xiii) Summit Lower Tie Bar : $110 w/install
xiv) DC Sports Lower Tie Bar :
xv) Neuspeed Lower Tie Bar :
xvi) Front ARB : 25.4mm JDM ES ($180 with installation)
xvii) Rear ARB : 22mm DC5 ($180 with installation)



Brake System

Front Brakes Upgrade Kit

i) Prelude Recon : 282mm rotor + Bigger caliper ($380-$420)
ii) Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
iii) Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
iv) VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
v) FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($450-$600)

Rotors and Brake Pads

i) Brembo max slotted rotor with project mu bestop brake pads ($280 with install)
ii) Brembo Sports Rotors (slotted or cross drilled) : $380
iii) Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install
iv) project Mu bestop Brake Pads: $120 with install
v) Brembo blank rotor(282mm) redrilled: $220 w/install
vi) Ferrodo Brake Pads: $110 w/install
vii) Hawk performance pads: pm Bravo for special pricing


Project Miu Rotors, Pads - Go to Stamford Tyres (esp at Jurong)

Brembo stuff and Hawk pads, go to bro Bro
Can look for bravo here:

SPINERGY CONCEPTS
Blk 9002 Tampines St 93
#02-40 S(528836)
T: 6786 2809 (Mon~Fri, 9am~5pm - by appmt)
E: spinergyconcepts@singnet.com.sg




Rear disc conversion

i) ES3 conversion: approx $1.3k (direct plug n play, no mods req, rotor sz 260mm)
ii) EP3 conversion: approx $950 (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iii) DC5 conversion: POA (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iv) EK4 conversion: approx $800 (need to fabricate bracket, rotor sz 240mm)

Stainless steel braided hoses aka (SSBH)

i) EZess Steel braided brake hose with Teflon(4piece): $280 -$320 w/install
ii) Pro-RS PTFE Teflon Steel Braided brake hose (4piece) + 1L Ferodo brake fluid: $240 w/install
iii) Goodridge Steel braided brake hose: $200+ (front only)


Tyres

*Price depends on width and profile*

15in

i) Yokohama Advan AD07 15" 195/55/15 ($135-150)
ii) Falken RT215 15" 205/50/15 ($130-160)
iii) Goodyear Eagle F1 GSD3 [Thai]195/60/15 ($110-130)
iv) Bridgestone G3 15" ($90-120)
v) ContiPremiumContact2: 195/45/15 ($220)
vi) Hankook Ventus Prime K105 205/55R15 ($115-130each)
vii) Bridgestone RE01R 195/55/15($155-185)
viii) Bridgestone RE001 Adreneline 195/55/15($120-145)
ix) Goodyear Eagle RS Sports 195/55/15 [Made in Japan] $145
x) Goodyear Eagle Asymetric [Made in Japan] $155
xi) Toyo Proxes T1R 195/55/15$120
xii) Toyo Proxes R1R 195/55/15 $175
xiii) Toyo Proxes R888 195/55/15$175

16in

i) Yokohama ADrive R1 205/50/16 ($130)
ii) Bridgestone G3 205/50/16 inch ($130)
iii) Goodyear Eagle F1 GSD3 [Thai] 16" ($120)
iv) Toyo Proxes T1R 205/50/16 ($150/pcs)
v) Yokohama SDrive 205/50/16 ($160)
vi) Falken Ziex 326 205/50/16 ($120)


17in

i) ContiSportsContact2: 215/45/17VR ($280)
ii) Dunlop LM702: 215/45/17 ($150)
iii) Goodyear Eagle F1 GSD3: 205/45/17 [Thai] ($160)
iv) Toyo T1R: 215/45/17 ($200)
v) Bridgestone RE001: 215/45/17 ($220)
vi) Bridgestone RE01R: 215/45/17 ($250)
vii) ContiSportsContact3: 215/45ZR/17W TL XL ($300)


Electronics

i) Apex'i turbo timer: ($160)
ii) Unichip ($800+)
iii) Greddy E-manage Blue : ($500+)
iv) Apex'i VAFCII (less than $500) without install or tuning
v) Apex'i SAFCII:
vi) Apex'i RSM : $310
vii) Blitz RVit : $480
viii) Defi VSD basic: $290+
ix) HKS F-Con SZ : Install & Tune ( RM2600 )
x) SMT6: $800+
xi) Greddy E-manage Ultimate: ($1500) install+tune
xii) Pivot Raizin Voltage Stabilizer VS $98 w/o install
xiii) Pivot Raizin Voltage Stabilizer + Grounding VS-E $148 w/o install
xiv) Pivot Raizin Spark VS-S $128 w/o install
xv) Pivot Raizin Spark VS-V $228 w/o install
xvi) Pivot Spark Earth $98 w/o install

Accessories

i) CF eylids : ($180)
ii) Custom make Rear eyelids : ($220)
iii) CF hood (OEM design) : $890 (MSRP)
iv) Billion Funnel : ($55) :x
v) Bonnet Insulator: ($55)
vi) Boot Insulator: ($90)
vii) Billion Air Duct: ($150 per metre)
viii) RPM Crank Pulley with Harmonic Damper ($270)



Emblems

i) EP3 original Honda emblem : chrome 'H', red background ($60)
ii) VTEC emblem : wordings onli ($13)
iii) i-VTEC emblem : wordings onli (unknown)
iv) sticker type VTEC emblem : silver color wordings($6)
v) JDM 'FERIO' Emblem : $25
vi) Rear 'RS' Emblem : $43
vii) Front 'RS' Emblem : $19
viii) Mugen Emblem : $12


Bonnet Chrome Tip

i) Sticker: in matt/gloss black (Ask Eeee78 for Pricing)
paint on chrome strip : ($25 - $30)
ii) Removal of chrome strip + sealing up holes on bonnet + respray bonnet : ($180)
iii) Honda Original Colour Coded Grille (for ES8 & pre f/l ES5) : $63


Boot Chrome Tip

i) Sticker: (Ask Eeee78 for Pricing)
ii) Painted Chrome Tip : Front / Rear ($70)
iii) Removal of Whole Chrome Part (ard 100+)
iv) Honda Original Colour Coded Trunk (for ES8 & pre f/l ES5) : $72

Interior

i) Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.


*Prices varies, kindly call and find out actual pricing from the relevant suppliers/shops.*



Maintenance List

Aircon Compressor Unit

Markcool at Woodlands, New $460, recon $220, labour inclusive.
Radiator Fan Motor, New $120
Look for Ah Huat, a real honest and friendly guy.

Posted: Wed Jun 03, 2009 4:03 pm
by Wham
Poison List

Intake /Header / Exhaust

Intake

i) Simota Aeroform : SRI with Plastic Heatshield (ard $230)
ii) Blitz Sonic : SRI with Aluminium Heatshield (w/o piping) ($560+/-)
iii) BMC : CDA ($440-480) w/o install depending on size. Auto smaller
iv) Apexi : SRI (Around 180 plus $20 bucks for adaptor)
v) K&N : Drop-in with CAI piping (less than $150)
vi) AEM V1: CAI piping with AEM open pod filter ($500+)
vii) AEM V2: SRI piping with AEM open pod filter ($570+)
viii) K&N : Open pod (model 57i) ($250)
ix) INJEN : SRI open pod : ~$400
x) NINJA-RACING: All-in-one, piping, close pod and CAI ($373)
xi) Throttle body: (S$320) include installation plus anaylsis fault.

Header

i) Hotbits Header : 4-2-1 Header (Ard $250) with flexi pipe
ii) SD Header (Non-Chrome) : 4-2-1 Header ($250) with flexi pipe from FK
iii) SD Header (Chrome) : 4-1 ($200) From FK
vi) DC sports Header 4-2-1 (Ard $700)
v) Megan Racing Sports Header 4-1 (Chrome) (Ard $240) (not available in S'pore, order from Amazon) Product No: MR-SSH-HC117

Exhaust

i) Supersprint : free flow muffler ($784 + $50 inspection fee, LTA approved)
ii) Hotbits : Straight through muffler ($140 with install, non LTA approved)
iii) Operated : Stock exhuast ($180++, non LTA approved)



Cooling

i) Mugen thermostat and fan switch: approx $250




Engine Oil Cooler:

ATF Cooler:

i) Hayden : $240+ w install
ii) HKS : SGD 1100
iii) ARC : SGD 2300
iv) Permacool: $220 w install



Suspension

Camber Kit :

i) SPC Front Camber Bolts : $130
ii) SPC Rear Camber Kits : $350
iii) J's Racing Rear Cambar Kit ( Ball Joint ): $ 500
iv) Kenny's Modified Stock Rear Camber Kits : $200+

Lowering Springs :

i) Tanabe NF210 (S$370++ w/install)
ii) APEX (S$350 w/install)
iii) Eibach Pro kit : $480

Coilover :

i) BC Coilover :Height + Damping Adjustatable (Ard $1250)
ii) Tomei Coilover : Height + Damping Adjustatable (Ard $980)
iii) Tein Coilover: Height + Damping Adjustatable (Ard $1800 for Tein SS)
iv) Tein Basic: Height Adjustable, Can Revalve ( RM2700)
v) Tanabe Coilover : Height Adjustatable only (ard $1900)
vi) D2 Coilover : Height + Damping Adjustatable + pillowball mount (ard $1700) best buy
vii) Hotbits Coilovers: Height adjustable only, RM2000. Revalve whole set RM480

Bars (Struts, ARBs)

i) Hotbits Tower Strut bar : ($85)
ii) Alutec Tower Strut bar : ($155)
iii) Neuspeed Tower Strut bar : ($230)
iv) Silver Front Strut Bar : ($110 w/install)
v) Summit Front Strut Bar: ($150 w/install)
vi) Summit Rear Strut Bar: ($180 w/install)
vii) DC sport front strut bar:(ard $500 w/install)
viii) OEM ES Engine Strut Bar : $75 w/ install
ix) Summit Lower Brace Bars : 2 point Bars x2 ($250 w/install)
x) Tanabe Lower Brace Bars : 4 point Bar ($250 w/install)
xi) Neuspeed X-Brace : 4 point
xii) Alutec Lower Tie Bar : ($100 w/install)
xiii) Summit Lower Tie Bar : $110 w/install
xiv) DC Sports Lower Tie Bar :
xv) Neuspeed Lower Tie Bar :
xvi) Front ARB : 25.4mm JDM ES ($180 with installation)
xvii) Rear ARB : 22mm DC5 ($180 with installation)



Brake System

Front Brakes Upgrade Kit

i) Prelude Recon : 282mm rotor + Bigger caliper ($380-$420)
ii) Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
iii) Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
iv) VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
v) FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($450-$600)

Rotors and Brake Pads

i) Brembo max slotted rotor with project mu bestop brake pads ($280 with install)
ii) Brembo Sports Rotors (slotted or cross drilled) : $380
iii) Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install
iv) project Mu bestop Brake Pads: $120 with install
v) Brembo blank rotor(282mm) redrilled: $220 w/install
vi) Ferrodo Brake Pads: $110 w/install
vii) Hawk performance pads: pm Bravo for special pricing


Project Miu Rotors, Pads - Go to Stamford Tyres (esp at Jurong)

Brembo stuff and Hawk pads, go to bro Bro
Can look for bravo here:

SPINERGY CONCEPTS
Blk 9002 Tampines St 93
#02-40 S(528836)
T: 6786 2809 (Mon~Fri, 9am~5pm - by appmt)
E: spinergyconcepts@singnet.com.sg




Rear disc conversion

i) ES3 conversion: approx $1.3k (direct plug n play, no mods req, rotor sz 260mm)
ii) EP3 conversion: approx $950 (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iii) DC5 conversion: POA (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iv) EK4 conversion: approx $800 (need to fabricate bracket, rotor sz 240mm)

Stainless steel braided hoses aka (SSBH)

i) EZess Steel braided brake hose with Teflon(4piece): $280 -$320 w/install
ii) Pro-RS PTFE Teflon Steel Braided brake hose (4piece) + 1L Ferodo brake fluid: $240 w/install
iii) Goodridge Steel braided brake hose: $200+ (front only)


Tyres

*Price depends on width and profile*

15in

i) Yokohama Advan AD07 15" 195/55/15 ($135-150)
ii) Falken RT215 15" 205/50/15 ($130-160)
iii) Goodyear Eagle F1 GSD3 [Thai]195/60/15 ($110-130)
iv) Bridgestone G3 15" ($90-120)
v) ContiPremiumContact2: 195/45/15 ($220)
vi) Hankook Ventus Prime K105 205/55R15 ($115-130each)
vii) Bridgestone RE01R 195/55/15($155-185)
viii) Bridgestone RE001 Adreneline 195/55/15($120-145)
ix) Goodyear Eagle RS Sports 195/55/15 [Made in Japan] $145
x) Goodyear Eagle Asymetric [Made in Japan] $155
xi) Toyo Proxes T1R 195/55/15$120
xii) Toyo Proxes R1R 195/55/15 $175
xiii) Toyo Proxes R888 195/55/15$175
xiv) Federal 595SS: 195/55/15 - $88
xv) Federal 595EVO: 195/55/15 - $100



16in

i) Yokohama ADrive R1 205/50/16 ($130)
ii) Bridgestone G3 205/50/16 inch ($130)
iii) Goodyear Eagle F1 GSD3 [Thai] 16" ($120)
iv) Toyo Proxes T1R 205/50/16 ($150/pcs)
v) Yokohama SDrive 205/50/16 ($160)
vi) Falken Ziex 326 205/50/16 ($120)


17in

i) ContiSportsContact2: 215/45/17VR ($280)
ii) Dunlop LM702: 215/45/17 ($150)
iii) Goodyear Eagle F1 GSD3: 205/45/17 [Thai] ($160)
iv) Toyo T1R: 215/45/17 ($200)
v) Bridgestone RE001: 215/45/17 ($220)
vi) Bridgestone RE01R: 215/45/17 ($250)
vii) ContiSportsContact3: 215/45ZR/17W TL XL ($300)
viii) Federal 595SS: 215/45/17 ($130)
ix) Federal 595EVO: 215/45/17 ($138)
x) Federal 595RPM: 215/45/17 ($150)


Electronics

i) Apex'i turbo timer: ($160)
ii) Unichip ($800+)
iii) Greddy E-manage Blue : ($500+)
iv) Apex'i VAFCII (less than $500) without install or tuning
v) Apex'i SAFCII:
vi) Apex'i RSM : $310
vii) Blitz RVit : $480
viii) Defi VSD basic: $290+
ix) HKS F-Con SZ : Install & Tune ( RM2600 )
x) SMT6: $800+
xi) Greddy E-manage Ultimate: ($1500) install+tune
xii) Pivot Raizin Voltage Stabilizer VS $98 w/o install
xiii) Pivot Raizin Voltage Stabilizer + Grounding VS-E $148 w/o install
xiv) Pivot Raizin Spark VS-S $128 w/o install
xv) Pivot Raizin Spark VS-V $228 w/o install
xvi) Pivot Spark Earth $98 w/o install

Accessories

i) CF eylids : ($180)
ii) Custom make Rear eyelids : ($220)
iii) CF hood (OEM design) : $890 (MSRP)
iv) Billion Funnel : ($55) :x
v) Bonnet Insulator: ($55)
vi) Boot Insulator: ($90)
vii) Billion Air Duct: ($150 per metre)
viii) RPM Crank Pulley with Harmonic Damper ($270)



Emblems

i) EP3 original Honda emblem : chrome 'H', red background ($60)
ii) VTEC emblem : wordings onli ($13)
iii) i-VTEC emblem : wordings onli (unknown)
iv) sticker type VTEC emblem : silver color wordings($6)
v) JDM 'FERIO' Emblem : $25
vi) Rear 'RS' Emblem : $43
vii) Front 'RS' Emblem : $19
viii) Mugen Emblem : $12


Bonnet Chrome Tip

i) Sticker: in matt/gloss black (Ask Eeee78 for Pricing)
paint on chrome strip : ($25 - $30)
ii) Removal of chrome strip + sealing up holes on bonnet + respray bonnet : ($180)
iii) Honda Original Colour Coded Grille (for ES8 & pre f/l ES5) : $63


Boot Chrome Tip

i) Sticker: (Ask Eeee78 for Pricing)
ii) Painted Chrome Tip : Front / Rear ($70)
iii) Removal of Whole Chrome Part (ard 100+)
iv) Honda Original Colour Coded Trunk (for ES8 & pre f/l ES5) : $72

Interior

i) Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.


*Prices varies, kindly call and find out actual pricing from the relevant suppliers/shops.*



Maintenance List

Aircon Compressor Unit

Markcool at Woodlands, New $460, recon $220, labour inclusive.
Radiator Fan Motor, New $120
Look for Ah Huat, a real honest and friendly guy.


Thian Seng Motors Pte Ltd
Blk 261 Waterloo Auto Centre
Waterloo Street #01-22/02-24
Singapore 180261
Tel: 63371795, 63369777
Fax: 63361670
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Thian Seng Motors Pte Ltd
Blk 119 Bukit Merah Lane 1 #01-28 Singapore 151119
Tel: 62782407, 62782408, 62741110
Fax: 2782407
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Thian Seng Motors Pte Ltd
No 122 Eunos Ave 7
Richfield Centre #01-07
Singapore 409575
Tel: 67433124, 67433651
Fax: 67432651
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Posted: Sun Sep 13, 2009 10:17 am
by MCDS
Poison List

Intake /Header / Exhaust

Intake

i) Simota Aeroform : SRI with Plastic Heatshield (ard $230)
ii) Blitz Sonic : SRI with Aluminium Heatshield (w/o piping) ($560+/-)
iii) BMC : CDA ($440-480) w/o install depending on size. Auto smaller
iv) Apexi : SRI (Around 180 plus $20 bucks for adaptor)
v) K&N : Drop-in with CAI piping (less than $150)
vi) AEM V1: CAI piping with AEM open pod filter ($500+)
vii) AEM V2: SRI piping with AEM open pod filter ($570+)
viii) K&N : Open pod (model 57i) ($250)
ix) INJEN : SRI open pod : ~$400
x) NINJA-RACING: All-in-one, piping, close pod and CAI ($373)
xi) Throttle body: (S$320) include installation plus anaylsis fault.

Header

i) Hotbits Header : 4-2-1 Header (Ard $250) with flexi pipe
ii) SD Header (Non-Chrome) : 4-2-1 Header ($250) with flexi pipe from FK
iii) SD Header (Chrome) : 4-1 ($200) From FK
vi) DC sports Header 4-2-1 (Ard $700)
v) Megan Racing Sports Header 4-1 (Chrome) (Ard $240) (not available in S'pore, order from Amazon) Product No: MR-SSH-HC117

Exhaust

i) Supersprint : free flow muffler ($784 + $50 inspection fee, LTA approved)
ii) Hotbits : Straight through muffler ($140 with install, non LTA approved)
iii) Operated : Stock exhuast ($180++, non LTA approved)



Cooling

i) Mugen thermostat and fan switch: approx $250




Engine Oil Cooler:

ATF Cooler:

i) Hayden : $240+ w install
ii) HKS : SGD 1100
iii) ARC : SGD 2300
iv) Permacool: $220 w install



Suspension

Camber Kit :

i) SPC Front Camber Bolts : $130
ii) SPC Rear Camber Kits : $350
iii) J's Racing Rear Cambar Kit ( Ball Joint ): $ 500
iv) Kenny's Modified Stock Rear Camber Kits : $200+

Lowering Springs :

i) Tanabe NF210 (S$370++ w/install)
ii) APEX (S$350 w/install)
iii) Eibach Pro kit : $480

Coilover :

i) BC Coilover :Height + Damping Adjustatable (Ard $1250)
ii) Tomei Coilover : Height + Damping Adjustatable (Ard $980)
iii) Tein Coilover: Height + Damping Adjustatable (Ard $1800 for Tein SS)
iv) Tein Basic: Height Adjustable, Can Revalve ( RM2700)
v) Tanabe Coilover : Height Adjustatable only (ard $1900)
vi) D2 Coilover : Height + Damping Adjustatable + pillowball mount (ard $1700) best buy
vii) Hotbits Coilovers: Height adjustable only, RM2000. Revalve whole set RM480

Bars (Struts, ARBs)

i) Hotbits Tower Strut bar : ($85)
ii) Alutec Tower Strut bar : ($155)
iii) Neuspeed Tower Strut bar : ($230)
iv) Silver Front Strut Bar : ($110 w/install)
v) Summit Front Strut Bar: ($150 w/install)
vi) Summit Rear Strut Bar: ($180 w/install)
vii) DC sport front strut bar:(ard $500 w/install)
viii) OEM ES Engine Strut Bar : $75 w/ install
ix) Summit Lower Brace Bars : 2 point Bars x2 ($250 w/install)
x) Tanabe Lower Brace Bars : 4 point Bar ($250 w/install)
xi) Neuspeed X-Brace : 4 point
xii) Alutec Lower Tie Bar : ($100 w/install)
xiii) Summit Lower Tie Bar : $110 w/install
xiv) DC Sports Lower Tie Bar :
xv) Neuspeed Lower Tie Bar :
xvi) Front ARB : 25.4mm JDM ES ($180 with installation)
xvii) Rear ARB : 22mm DC5 ($180 with installation)



Brake System

Front Brakes Upgrade Kit

i) Prelude Recon : 282mm rotor + Bigger caliper ($380-$420)
ii) Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
iii) Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
iv) VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
v) FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($450-$600)

Rotors and Brake Pads

i) Brembo max slotted rotor with project mu bestop brake pads ($280 with install)
ii) Brembo Sports Rotors (slotted or cross drilled) : $380
iii) Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install
iv) project Mu bestop Brake Pads: $120 with install
v) Brembo blank rotor(282mm) redrilled: $220 w/install
vi) Ferrodo Brake Pads: $110 w/install
vii) Hawk performance pads: pm Bravo for special pricing


Project Miu Rotors, Pads - Go to Stamford Tyres (esp at Jurong)

Brembo stuff and Hawk pads, go to bro Bro
Can look for bravo here:

SPINERGY CONCEPTS
Blk 9002 Tampines St 93
#02-40 S(528836)
T: 6786 2809 (Mon~Fri, 9am~5pm - by appmt)
E: spinergyconcepts@singnet.com.sg




Rear disc conversion

i) ES3 conversion: approx $1.3k (direct plug n play, no mods req, rotor sz 260mm)
ii) EP3 conversion: approx $950 (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iii) DC5 conversion: POA (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iv) EK4 conversion: approx $800 (need to fabricate bracket, rotor sz 240mm)

Stainless steel braided hoses aka (SSBH)

i) EZess Steel braided brake hose with Teflon(4piece): $280 -$320 w/install
ii) Pro-RS PTFE Teflon Steel Braided brake hose (4piece) + 1L Ferodo brake fluid: $240 w/install
iii) Goodridge Steel braided brake hose: $200+ (front only)


Tyres

*Price depends on width and profile*

15in

i) Yokohama Advan AD07 15" 195/55/15 ($135-150)
ii) Falken RT215 15" 205/50/15 ($130-160)
iii) Goodyear Eagle F1 GSD3 [Thai]195/60/15 ($110-130)
iv) Bridgestone G3 15" ($90-120)
v) ContiPremiumContact2: 195/45/15 ($220)
vi) Hankook Ventus Prime K105 205/55R15 ($115-130each)
vii) Bridgestone RE01R 195/55/15($155-185)
viii) Bridgestone RE001 Adreneline 195/55/15($120-145)
ix) Goodyear Eagle RS Sports 195/55/15 [Made in Japan] $145
x) Goodyear Eagle Asymetric [Made in Japan] $155
xi) Toyo Proxes T1R 195/55/15$120
xii) Toyo Proxes R1R 195/55/15 $175
xiii) Toyo Proxes R888 195/55/15$175
xiv) Federal 595SS: 195/55/15 - $88
xv) Federal 595EVO: 195/55/15 - $100



16in

i) Yokohama ADrive R1 205/50/16 ($130)
ii) Bridgestone G3 205/50/16 inch ($130)
iii) Goodyear Eagle F1 GSD3 [Thai] 16" ($120)
iv) Toyo Proxes T1R 205/50/16 ($150/pcs)
v) Yokohama SDrive 205/50/16 ($160)
vi) Falken Ziex 326 205/50/16 ($120)


17in

i) ContiSportsContact2: 215/45/17VR ($280)
ii) Dunlop LM702: 215/45/17 ($150)
iii) Goodyear Eagle F1 GSD3: 205/45/17 [Thai] ($160)
iv) Toyo T1R: 215/45/17 ($200)
v) Bridgestone RE001: 215/45/17 ($220)
vi) Bridgestone RE01R: 215/45/17 ($250)
vii) ContiSportsContact3: 215/45ZR/17W TL XL ($300)
viii) Federal 595SS: 215/45/17 ($130)
ix) Federal 595EVO: 215/45/17 ($138)
x) Federal 595RPM: 215/45/17 ($150)


Electronics

i) Apex'i turbo timer: ($160)
ii) Unichip ($800+)
iii) Greddy E-manage Blue : ($500+)
iv) Apex'i VAFCII (less than $500) without install or tuning
v) Apex'i SAFCII:
vi) Apex'i RSM : $310
vii) Blitz RVit : $480
viii) Defi VSD basic: $290+
ix) HKS F-Con SZ : Install & Tune ( RM2600 )
x) SMT6: $800+
xi) Greddy E-manage Ultimate: ($1500) install+tune
xii) Pivot Raizin Voltage Stabilizer VS $98 w/o install
xiii) Pivot Raizin Voltage Stabilizer + Grounding VS-E $148 w/o install
xiv) Pivot Raizin Spark VS-S $128 w/o install
xv) Pivot Raizin Spark VS-V $228 w/o install
xvi) Pivot Spark Earth $98 w/o install

Accessories

i) CF eylids : ($180)
ii) Custom make Rear eyelids : ($220)
iii) CF hood (OEM design) : $890 (MSRP)
iv) Billion Funnel : ($55) :x
v) Bonnet Insulator: ($55)
vi) Boot Insulator: ($90)
vii) Billion Air Duct: ($150 per metre)
viii) RPM Crank Pulley with Harmonic Damper ($270)



Emblems

i) EP3 original Honda emblem : chrome 'H', red background ($60)
ii) VTEC emblem : wordings onli ($13)
iii) i-VTEC emblem : wordings onli (unknown)
iv) sticker type VTEC emblem : silver color wordings($6)
v) JDM 'FERIO' Emblem : $25
vi) Rear 'RS' Emblem : $43
vii) Front 'RS' Emblem : $19
viii) Mugen Emblem : $12


Bonnet Chrome Tip

i) Sticker: in matt/gloss black (Ask Eeee78 for Pricing)
paint on chrome strip : ($25 - $30)
ii) Removal of chrome strip + sealing up holes on bonnet + respray bonnet : ($180)
iii) Honda Original Colour Coded Grille (for ES8 & pre f/l ES5) : $63


Boot Chrome Tip

i) Sticker: (Ask Eeee78 for Pricing)
ii) Painted Chrome Tip : Front / Rear ($70)
iii) Removal of Whole Chrome Part (ard 100+)
iv) Honda Original Colour Coded Trunk (for ES8 & pre f/l ES5) : $72

Interior

i) Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.


*Prices varies, kindly call and find out actual pricing from the relevant suppliers/shops.*



Maintenance List

Aircon Compressor Unit

Markcool at Woodlands, New $460, recon $220, labour inclusive.
Radiator Fan Motor, New $120
Look for Ah Huat, a real honest and friendly guy.


Thian Seng Motors Pte Ltd
Blk 261 Waterloo Auto Centre
Waterloo Street #01-22/02-24
Singapore 180261
Tel: 63371795, 63369777
Fax: 63361670
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Thian Seng Motors Pte Ltd
Blk 119 Bukit Merah Lane 1 #01-28 Singapore 151119
Tel: 62782407, 62782408, 62741110
Fax: 2782407
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Thian Seng Motors Pte Ltd
No 122 Eunos Ave 7
Richfield Centre #01-07
Singapore 409575
Tel: 67433124, 67433651
Fax: 67432651
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg


Tanly is also located at Waterloo Centre... if TS dun have stock , give Tanly a try. Sometimes, they have stock...


Drive Shaft problems (yeah the ES is getting old enough to have this problem now in 2009... so here's a recommended workshop to help check things out if your car goes tok tok tok when turning for parking, when steering is turned to lock.)

Elite Car Drive Shaft Centre
Blk 21 Sin Ming Ind Est Sec A #01-38 Singapore 575679
Tel : 6482 0215

Look for Jason & get him to check. Friendly guy.

This contact contributed by bro Fusion28

Posted: Sat Sep 26, 2009 12:45 pm
by DaDude
Poison List

Intake /Header / Exhaust

Intake

Simota Aeroform : SRI with Plastic Heatshield (ard $230)
Blitz Sonic : SRI with Aluminium Heatshield (w/o piping) ($550+/-)
BMC : CDA ($440-480) w/o install depending on size. Auto smaller
Apexi : SRI (Around 180 plus $20 bucks for adaptor)
K&N : Drop-in with CAI piping (less than $150)
AEM V1: CAI piping with AEM open pod filter ($500+)
AEM V2: SRI piping with AEM open pod filter ($570+)
K&N : Open pod (model 57i) ($250)
INJEN : SRI open pod : ~$400
NINJA-RACING: All-in-one, piping, close pod and CAI ($373)
Throttle body: (S$320-380) include installation plus anaylsis fault.

Header

Hotbits Header : 4-2-1 Header (Ard $250) with flexi pipe
SD Header (Non-Chrome) : 4-2-1 Header ($250) with flexi pipe from FK
SD Header (Chrome) : 4-1 ($200) From FK
DC sports Header 4-2-1 ($890 with shipment, by order only)

Exhaust

Supersprint : free flow muffler ($784 + $50 inspection fee, LTA approved)
Hotbits : Straight through muffler ($140 with install, non LTA approved)
Operated : Stock exhuast ($180++, non LTA approved)



Cooling

Mugen thermostat and fan switch: approx $250
Spoon thermostat ($140 with install)



Engine Oil Cooler:

ATF Cooler:

Hayden : $240+ w install
HKS : SGD 1100
ARC : SGD 2300
Permacool: $110-150 w install



Suspension

Camber Kit :

SPC Front Camber Bolts : $130
SPC Rear Camber Kits : $350
J's Racing Rear Cambar Kit ( Ball Joint ): $ 500
Kenny's Modified Stock Rear Camber Kits : $200+

Lowering Springs :

Tanabe NF210 (S$370++ w/install)
APEX (S$350 w/install)
Eibach Pro kit : $480

Coilover :

BC Coilover :Height + Damping Adjustatable ($1200+/-)
Tomei Coilover : Height + Damping Adjustatable (Ard $980)
Tein Coilover: Height + Damping Adjustatable (Ard $1800 for Tein SS)
Tein Basic: Height Adjustable, Can Revalve ( RM2700)
Tanabe Coilover : Height Adjustatable only (ard $1900)
D2 Coilover : Height + Damping Adjustatable + pillowball mount (ard $1400+/-)
Hotbits Coilovers: Height adjustable only, RM2000. Revalve whole set RM480

Bars (Struts, ARBs)

Hotbits Tower Strut bar : ($85)
Alutec Tower Strut bar : ($155)
Neuspeed Tower Strut bar : ($230)
Silver Front Strut Bar : ($110 w/install)
Summit Front Strut Bar: ($150 w/install)
Summit Rear Strut Bar: ($180 w/install)
DC sport front strut bar:(ard $500 w/install)
OEM ES Engine Strut Bar : $75 w/ install
Summit Lower Brace Bars : 2 point Bars x2 ($250 w/install)
Tanabe Lower Brace Bars : 4 point Bar ($250 w/install)
Neuspeed X-Brace : 4 point
Alutec Rear Strut bar: ($140 winstall)
Alutec Lower Tie Bar : ($100 w/install)
Summit Lower Tie Bar : $110 w/install
DC Sports Lower Tie Bar :
Neuspeed Lower Tie Bar :
Front ARB : 25.4mm JDM ES ($180 with installation)
Rear ARB : 22mm DC5 ($180 with installation)
Rear ARB : 19mm GSR($130 with installation)


Brake System

Front Brakes Upgrade Kit

Prelude Recon : 282mm rotor + Bigger caliper ($350-$450)
Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($380-$500)
Project Mu Slim 4pot anodised caliper, fitment on 15" and custom brackets (Approx $3500 w/install)

Rotors and Brake Pads

Brembo max 262mm slotted rotor with project mu bestop brake pads ($280 with install)
Brembo Sports Rotors (slotted or cross drilled 262mm) : $380
Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install
Project Mu HC+ ($380-420)
Project Mu HC+ rear setup, DC/EP ($280-320)
Project Mu bestop Brake Pads: $100-$120 w/install
AP 2pc floating rotor with 282mm slotted ($800)
Brembo blank rotor(282mm) redrilled: $200 w/install
Ferrodo Brake Pads: $110 w/install
Hawk performance pads: pm Bravo for special pricing



Project Miu Rotors, Pads - Go to Stamford Tyres (esp at Jurong)

Brembo stuff and Hawk pads, go to bro Bro
Can look for bravo here:

SPINERGY CONCEPTS
Blk 9002 Tampines St 93
#02-40 S(528836)
T: 6786 2809 (Mon~Fri, 9am~5pm - by appmt)
E: spinergyconcepts@singnet.com.sg




Rear disc conversion

ES3 conversion: approx $1k (direct plug n play, no mods req, rotor sz 262mm)
EP3 conversion: approx $1.2k (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 262mm)
DC5 conversion: $1k (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 262mm)
EK4 conversion: approx $800 (need to fabricate bracket, rotor sz 240mm)

Stainless steel braided hoses aka (SSBH)

i) EZess Steel braided brake hose with Teflon(4piece): $280 -$320 w/install
ii) Pro-RS PTFE Teflon Steel Braided brake hose (4piece) + 1L Ferodo brake fluid: $240 w/install
iii) Goodridge Steel braided brake hose: $200+ (front only)


Tyres

*Price depends on width and profile*

15in

Yokohama Advan AD07 15" 195/55/15 ($135-150)
Yokohama Advan AD08 195/50/15 ($195-$205)
Falken RT215 15" 205/50/15 ($130-160)
Goodyear Eagle F1 GSD3 [Thai]195/60/15 ($110-130)
Bridgestone G3 15" ($90-120)
ContiPremiumContact2: 195/45/15 ($220)
Hankook Ventus Prime K105 205/55R15 ($115-130)
Bridgestone RE01R 195/55/15($155-195) - Discontinued
Bridgestone RE001 Adreneline 195/55/15($120-145)
Bridgestone RE11 195/55/15 ($180-$205)
Bridgestone RE55 195/55/15 ($200-$225)
Goodyear Eagle RS Sports 195/55/15 [Made in Japan] $145
Goodyear Eagle Asymetric [Made in Japan] $155
Toyo Proxes T1R 195/55/15$120
Toyo Proxes R1R 195/55/15 $170
Toyo Proxes R888 195/55/15 $185

16in

i) Yokohama ADrive R1 205/50/16 ($130)
ii) Bridgestone G3 205/50/16 inch ($130)
iii) Goodyear Eagle F1 GSD3 [Thai] 16" ($120)
iv) Toyo Proxes T1R 205/50/16 ($150/pcs)
v) Yokohama SDrive 205/50/16 ($160)
vi) Falken Ziex 326 205/50/16 ($120)


17in

ContiSportsContact2: 215/45/17VR ($280)
Dunlop LM702: 215/45/17 ($150)
Goodyear Eagle F1 GSD3: 205/45/17 [Thai] ($160)
Toyo T1R: 215/45/17 ($200)
Bridgestone RE001: 215/45/17 ($220)
Bridgestone RE01R: 215/45/17 ($250)
ContiSportsContact3: 215/45ZR/17W TL XL ($300)


Electronics

Apex'i turbo timer: ($160)
Unichip ($800+)
Greddy E-manage Blue : ($500+)
Apex'i VAFCII (less than $500) without install or tuning
Apex'i SAFCII:
Apex'i RSM : $310
Blitz RVit : $480
Defi VSD basic: $290+
HKS F-Con SZ : Install & Tune ( RM2600 )
SMT6: $800+
Greddy E-manage Ultimate: ($1500) install+tune
Pivot Raizin Voltage Stabilizer VS $98 w/o install
Pivot Raizin Voltage Stabilizer + Grounding VS-E $148 w/o install
Pivot Raizin Spark VS-S $128 w/o install
Pivot Raizin Spark VS-V $228 w/o install
Pivot Spark Earth $98 w/o install

Accessories

CF eylids : ($180)
Custom make Rear eyelids : ($220)
CF Bonet (OEM design) : $900
Billion Funnel : ($55 aluminium, $80 CF)
Bonnet Insulator: ($55)
Boot Insulator: ($90)
Billion Air Duct: ($150 per metre)
RPM Crank Pulley with Harmonic Damper ($270)



Emblems

EP3 original Honda emblem : chrome 'H', red background ($60)
VTEC emblem : wordings onli ($13)
i-VTEC emblem : wordings onli (unknown)
sticker type VTEC emblem : silver color wordings($6)
JDM 'FERIO' Emblem : $25
Rear 'RS' Emblem : $43
Front 'RS' Emblem : $19
Mugen Emblem : $12


Bonnet Chrome Tip

Sticker: in matt/gloss black
paint on chrome strip : ($25 - $30)
Removal of chrome strip + sealing up holes on bonnet + respray bonnet : ($180)
Honda Original Colour Coded Grille (for ES8 & pre f/l ES5) : $63


Boot Chrome Tip

Painted Chrome Tip : Front / Rear ($70)
Removal of Whole Chrome Part (ard 100+)
Honda Original Colour Coded Trunk (for ES8 & pre f/l ES5) : $72

Interior

Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.


*Prices varies, kindly call and find out actual pricing from the relevant suppliers/shops.*



Maintenance List

Aircon Compressor Unit

Markcool at Woodlands, New $460, recon $220, labour inclusive.
Look for Ah Huat, a real honest and friendly guy.

Posted: Mon Nov 09, 2009 3:11 pm
by dave543
Any bro know the shop contact for lowering spring as mentioned above?

Posted: Mon Nov 09, 2009 5:16 pm
by DaDude
dave543 wrote:Any bro know the shop contact for lowering spring as mentioned above?
pm humble_evo, he might have a 2nd hand set for sale, as he is converting to a coilovers.

Posted: Wed Feb 03, 2010 9:59 am
by Daniel Tee
xvi) Front ARB : 25.4mm JDM ES ($180 with installation)

anybody knows where to get this item install? thks!

Posted: Wed Feb 03, 2010 2:56 pm
by ZenithSoul
can give thian seng a call. call their waterloo side.
last time i call they got rdy stock. around 120 for the arb nia.
u can find their number at the workshop directory located in the general discussion section!
hope this helps =D

Posted: Thu Feb 04, 2010 7:33 am
by stepper78
Front Brakes Upgrade Kit

Prelude Recon : 282mm rotor + Bigger caliper ($350-$450)
Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($380-$500)
Project Mu Slim 4pot anodised caliper, fitment on 15" and custom brackets (Approx $3500 w/install)


for the FD brake, is it direct fit to ES?

Any FDs or FD2 only?

Thanks.

Posted: Thu Feb 04, 2010 10:34 am
by MCDS
NOT a direct fit. got to modify and redrill the rotor to 4x100 PCD. FD are 5x114.3 holed rotors.

Posted: Mon Feb 08, 2010 7:28 am
by MCDS
In view of so many NEW owners of the ES coming in to our little ES corner and asking where and which workshop to service their rides, I think I should add a small section to the poison list of Workshops that we did try to use for the ES, with some satisfaction on workmanship and prices...

Previously, there was a thread on LOUSY workshops, but it's buried deep in the pages... maybe I should revive that and see how we can add on and not clutter this resource thread...

Watch this space...

Posted: Mon Feb 08, 2010 8:17 am
by MCDS
Poison List

Intake /Header / Exhaust

Intake

i) Simota Aeroform : SRI with Plastic Heatshield (ard $230)
ii) Blitz Sonic : SRI with Aluminium Heatshield (w/o piping) ($560+/-)
iii) BMC : CDA ($440-480) w/o install depending on size. Auto smaller
iv) Apexi : SRI (Around 180 plus $20 bucks for adaptor)
v) K&N : Drop-in with CAI piping (less than $150)
vi) AEM V1: CAI piping with AEM open pod filter ($500+)
vii) AEM V2: SRI piping with AEM open pod filter ($570+)
viii) K&N : Open pod (model 57i) ($250)
ix) INJEN : SRI open pod : ~$400
x) NINJA-RACING: All-in-one, piping, close pod and CAI ($373)
xi) Throttle body: (S$320) include installation plus anaylsis fault.

Header

i) Hotbits Header : 4-2-1 Header (Ard $250) with flexi pipe
ii) SD Header (Non-Chrome) : 4-2-1 Header ($250) with flexi pipe from FK
iii) SD Header (Chrome) : 4-1 ($200) From FK
vi) DC sports Header 4-2-1 (Ard $700)
v) Megan Racing Sports Header 4-1 (Chrome) (Ard $240) (not available in S'pore, order from Amazon) Product No: MR-SSH-HC117

Exhaust

i) Supersprint : free flow muffler ($784 + $50 inspection fee, LTA approved)
ii) Hotbits : Straight through muffler ($140 with install, non LTA approved)
iii) Operated : Stock exhuast ($180++, non LTA approved)



Cooling

i) Mugen thermostat and fan switch: approx $250




Engine Oil Cooler:

ATF Cooler:

i) Hayden : $240+ w install
ii) HKS : SGD 1100
iii) ARC : SGD 2300
iv) Permacool: $220 w install



Suspension

Camber Kit :

i) SPC Front Camber Bolts : $130
ii) SPC Rear Camber Kits : $350
iii) J's Racing Rear Cambar Kit ( Ball Joint ): $ 500
iv) Kenny's Modified Stock Rear Camber Kits : $200+

Lowering Springs :

i) Tanabe NF210 (S$370++ w/install)
ii) APEX (S$350 w/install)
iii) Eibach Pro kit : $480

Coilover :

i) BC Coilover :Height + Damping Adjustatable (Ard $1250)
ii) Tomei Coilover : Height + Damping Adjustatable (Ard $980)
iii) Tein Coilover: Height + Damping Adjustatable (Ard $1800 for Tein SS)
iv) Tein Basic: Height Adjustable, Can Revalve ( RM2700)
v) Tanabe Coilover : Height Adjustatable only (ard $1900)
vi) D2 Coilover : Height + Damping Adjustatable + pillowball mount (ard $1700) best buy
vii) Hotbits Coilovers: Height adjustable only, RM2000. Revalve whole set RM480

Bars (Struts, ARBs)

i) Hotbits Tower Strut bar : ($85)
ii) Alutec Tower Strut bar : ($155)
iii) Neuspeed Tower Strut bar : ($230)
iv) Silver Front Strut Bar : ($110 w/install)
v) Summit Front Strut Bar: ($150 w/install)
vi) Summit Rear Strut Bar: ($180 w/install)
vii) DC sport front strut bar:(ard $500 w/install)
viii) OEM ES Engine Strut Bar : $75 w/ install
ix) Summit Lower Brace Bars : 2 point Bars x2 ($250 w/install)
x) Tanabe Lower Brace Bars : 4 point Bar ($250 w/install)
xi) Neuspeed X-Brace : 4 point
xii) Alutec Lower Tie Bar : ($100 w/install)
xiii) Summit Lower Tie Bar : $110 w/install
xiv) DC Sports Lower Tie Bar :
xv) Neuspeed Lower Tie Bar :
xvi) Front ARB : 25.4mm JDM ES ($180 with installation)
xvii) Rear ARB : 22mm DC5 ($180 with installation)



Brake System

Front Brakes Upgrade Kit

i) Prelude Recon : 282mm rotor + Bigger caliper ($380-$420)
ii) Wilwood Dynalite: forged/billet mini 4 pot caliper w 310 mm rotors, SSBH, brakets, etc ($1330+ w/install)
iii) Brembo GT 4 pot : 315mm Slotted or Drilled HT Rotor ( Approx SGD 2500 w/install )
iv) VTTR mini 6 pot: 286/300 2 piece slotted/drilled rotor (SGD$1,600 wif install at RaceTech - Ricky)
v) FD Brake caliper/rotor conversion 282mm, bigger caliper like Prelude - only this set is NEW ($450-$600)

Rotors and Brake Pads

i) Brembo max slotted rotor with project mu bestop brake pads ($280 with install)
ii) Brembo Sports Rotors (slotted or cross drilled) : $380
iii) Project Mu SCR Pure Plus SD624 (262mm) Rotor : $480 with Install
iv) project Mu bestop Brake Pads: $120 with install
v) Brembo blank rotor(282mm) redrilled: $220 w/install
vi) Ferrodo Brake Pads: $110 w/install
vii) Hawk performance pads: pm Bravo for special pricing


Project Miu Rotors, Pads - Go to Stamford Tyres (esp at Jurong)

Brembo stuff and Hawk pads, go to bro Bro
Can look for bravo here:

SPINERGY CONCEPTS
Blk 9002 Tampines St 93
#02-40 S(528836)
T: 6786 2809 (Mon~Fri, 9am~5pm - by appmt)
E: spinergyconcepts@singnet.com.sg




Rear disc conversion

i) ES3 conversion: approx $1.3k (direct plug n play, no mods req, rotor sz 260mm)
ii) EP3 conversion: approx $950 (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iii) DC5 conversion: POA (need to fabricate bracket n re-drill rotors to 4x100, rotor sz 260mm)
iv) EK4 conversion: approx $800 (need to fabricate bracket, rotor sz 240mm)

Stainless steel braided hoses aka (SSBH)

i) EZess Steel braided brake hose with Teflon(4piece): $280 -$320 w/install
ii) Pro-RS PTFE Teflon Steel Braided brake hose (4piece) + 1L Ferodo brake fluid: $240 w/install
iii) Goodridge Steel braided brake hose: $200+ (front only)


Tyres

*Price depends on width and profile*

15in

i) Yokohama Advan AD07 15" 195/55/15 ($135-150)
ii) Falken RT215 15" 205/50/15 ($130-160)
iii) Goodyear Eagle F1 GSD3 [Thai]195/60/15 ($110-130)
iv) Bridgestone G3 15" ($90-120)
v) ContiPremiumContact2: 195/45/15 ($220)
vi) Hankook Ventus Prime K105 205/55R15 ($115-130each)
vii) Bridgestone RE01R This model is DISCONTINUED
viii) Bridgestone RE001 Adreneline 195/55/15($120-145)
ix) Goodyear Eagle RS Sports 195/55/15 [Made in Japan] $145
x) Goodyear Eagle Asymetric [Made in Japan] $155
xi) Toyo Proxes T1R 195/55/15$120
xii) Toyo Proxes R1R 195/55/15 $175
xiii) Toyo Proxes R888 195/55/15$175
xiv) Federal 595SS: 195/55/15 - $88
xv) Federal 595EVO: 195/55/15 - $100



16in

i) Yokohama ADrive R1 205/50/16 ($130)
ii) Bridgestone G3 205/50/16 inch ($130)
iii) Goodyear Eagle F1 GSD3 [Thai] 16" ($120)
iv) Toyo Proxes T1R 205/50/16 ($150/pcs)
v) Yokohama SDrive 205/50/16 ($160)
vi) Falken Ziex 326 205/50/16 ($120)


17in

i) ContiSportsContact2: 215/45/17VR ($280)
ii) Dunlop LM702: 215/45/17 ($150)
iii) Goodyear Eagle F1 GSD3: 205/45/17 [Thai] ($160)
iv) Toyo T1R: 215/45/17 ($200)
v) Bridgestone RE001: 215/45/17 ($220)
vi) Bridgestone RE01R: *DISCONTINUED
vii) ContiSportsContact3: 215/45ZR/17W TL XL ($300)
viii) Federal 595SS: 215/45/17 ($130)
ix) Federal 595EVO: 215/45/17 ($138)
x) Federal 595RPM: 215/45/17 ($150)


Electronics

i) Apex'i turbo timer: ($160)
ii) Unichip ($800+)
iii) Greddy E-manage Blue : ($500+)
iv) Apex'i VAFCII (less than $500) without install or tuning
v) Apex'i SAFCII:
vi) Apex'i RSM : $310
vii) Blitz RVit : $480
viii) Defi VSD basic: $290+
ix) HKS F-Con SZ : Install & Tune ( RM2600 )
x) SMT6: $800+
xi) Greddy E-manage Ultimate: ($1500) install+tune
xii) Pivot Raizin Voltage Stabilizer VS $98 w/o install
xiii) Pivot Raizin Voltage Stabilizer + Grounding VS-E $148 w/o install
xiv) Pivot Raizin Spark VS-S $128 w/o install
xv) Pivot Raizin Spark VS-V $228 w/o install
xvi) Pivot Spark Earth $98 w/o install

Accessories

i) CF eylids : ($180)
ii) Custom make Rear eyelids : ($220)
iii) CF hood (OEM design) : $890 (MSRP)
iv) Billion Funnel : ($55) :x
v) Bonnet Insulator: ($55)
vi) Boot Insulator: ($90)
vii) Billion Air Duct: ($150 per metre)
viii) RPM Crank Pulley with Harmonic Damper ($270)



Emblems

i) EP3 original Honda emblem : chrome 'H', red background ($60)
ii) VTEC emblem : wordings onli ($13)
iii) i-VTEC emblem : wordings onli (unknown)
iv) sticker type VTEC emblem : silver color wordings($6)
v) JDM 'FERIO' Emblem : $25
vi) Rear 'RS' Emblem : $43
vii) Front 'RS' Emblem : $19
viii) Mugen Emblem : $12


Bonnet Chrome Tip

i) Sticker: in matt/gloss black (Ask Eeee78 for Pricing)
paint on chrome strip : ($25 - $30)
ii) Removal of chrome strip + sealing up holes on bonnet + respray bonnet : ($180)
iii) Honda Original Colour Coded Grille (for ES8 & pre f/l ES5) : $63


Boot Chrome Tip

i) Sticker: (Ask Eeee78 for Pricing)
ii) Painted Chrome Tip : Front / Rear ($70)
iii) Removal of Whole Chrome Part (ard 100+)
iv) Honda Original Colour Coded Trunk (for ES8 & pre f/l ES5) : $72

Interior

i) Customised 3M Nomad Carmat with heel plate and grippers - $145(std), $175(sup) , $80 without heel plate and grippers.


*Prices varies, kindly call and find out actual pricing from the relevant suppliers/shops.*



Maintenance & Parts Supplier List

Aircon Compressor Unit

Markcool at Woodlands, New $460, recon $220, labour inclusive.
Radiator Fan Motor, New $120
Look for Ah Huat, a real honest and friendly guy.



Genuine/OEM Honda Parts
Thian Seng Motors Pte Ltd
Blk 261 Waterloo Auto Centre
Waterloo Street #01-22/02-24
Singapore 180261
Tel: 63371795, 63369777
Fax: 63361670
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Thian Seng Motors Pte Ltd
Blk 119 Bukit Merah Lane 1 #01-28 Singapore 151119
Tel: 62782407, 62782408, 62741110
Fax: 2782407
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg

Thian Seng Motors Pte Ltd
No 122 Eunos Ave 7
Richfield Centre #01-07
Singapore 409575
Tel: 67433124, 67433651
Fax: 67432651
URL: www.autoparts.com.sg/thianseng
Email: thiansengmotor@pacific.net.sg


Tanly is also located at Waterloo Centre... if TS dun have stock , give Tanly a try. Sometimes, they have stock...


Drive Shaft problems (yeah the ES is getting old enough to have this problem now in 2009... so here's a recommended workshop to help check things out if your car goes tok tok tok when turning for parking, when steering is turned to lock.)

Elite Car Drive Shaft Centre
Blk 21 Sin Ming Ind Est Sec A #01-38 Singapore 575679
Tel : 6482 0215

Look for Jason & get him to check. Friendly guy.

This contact contributed by bro Fusion28



General Servicing and Some Specialised Work, e.g. alignment, etc.

Kah Motors Leng Kee (look for Ah Wong, or Mr Wong)

Merlin @ Level 3 AMK AutopointII off AMK Ave5

Riverview @ Level 4 AMK AutopointII

Kenny's Alignment @ Level 4 AMK AutopointII for alignment + Camber ONLY

OSK @ Level 4 AMK AutopointII

GT Auto (Ah Yuen) electronics, meter installment, Simon Road

Soon Kiang Motor (Dr Heng) Blk 13 Defu Lane 10 - specialist works only pls.
*Next to Soon Kiang is a Spray Painting WS quite reputable and does good job... dunno the name - any bros here to help out?


Speedworks (Singapore) for IHE and electronics parts (Mr Loo) opp SPH on Tannery Lane

Miki Marketing - Sparco seats, Redline Oils, lots of performance parts -
(Address?) 67491996


Stamford Tyres (various branches, Jurong, Loyang, etc. pls google for more details - the two above showrooms worth going to for nice shopping for car accessories and detailing supplies)


Autobacs - one branch off Upp Bt Timah, other branch in Ubi - google for address? or other bros pls provide addy here

Silent - wa this one is growing... got club in ex-Punggol Marina - now called the Marina Country Club? (MCC). Showroom and ws in Ubi

Express Motion (Mary) Upp Thomson Road near Mandai T Junction next to the Shell petrol station. -- good installer of alarm, meters, and mid-low end ICE, simple oil change, polish, etc. and Brembo Brake COVERS!!

Driven (Joel) Wilwood BBK?

Espace Service Centre (Peter) Ubi Rd 1 (premium service at premium price but you get what you pay for)

There are many more, pls add in...

Posted: Mon Apr 12, 2010 3:17 am
by thunderca
Hi any bros know where still got sell goodridge ssbh? Happen to come across this thread. I am currently driving a ge6. Thanks.